ASTM D-70 / AASHTO T-228 For determining the specific gravity of semi – solid bituminous materials, asphalt cement, and soft tar pitches by use of a picnometer.
Consist of :
Picnometer : Hubbart type, 24 ml capacity …..1pcs
Picnometer : Hubbart type, 25 ml capacity …..1pcs
Thermometer : Astm 12 C, 20 to 102°C …..1ps
Dimension (l x w x h): 20 x 20 x 20 cm / Gross weight: 3 Kg
ASTM D-36 / AASHTO T-53; According SNI 06-2434-1991 For determining softening point of asphalt and tar usingthe ring and ball methode.
Consist of :
Shouldered Ring Assembly : machine brass, height adjusment 1 set
Standard Ball : steel ball, 9.52mm diameter 2 pcs
Flash Support : mesh wire gauze variable height adjusment 1 set
Support Assembly : Metal, provided with thermometer holder 1 set
Bunsen Burner : Heat resources 1 pcs
Asbestos Wire Gauze : Asbestos centre, 15 cm x 15 cm 1 pcs
Beaker Glass : 1000 ml capacity 1 pcs
Thermometer : ASTM 15 C, 2 to 80°C 1 pcs
Dimension (l x w x h): 90 x 30 x 30 cm / Gross weight: 10 Kg
Standard supply with instruction manual books
Kategori : Alat Laboratorium Aspal dan Jalan Raya
Flash and Fire Point by Cleveland Open Cup
Flash and Fire Point by Cleveland Open Cup
ASTM D-92 / AASHTO T-48 For determining flash and fire point by cleveland open cup for petroleum product and other liquids, except fuel oils and materials having an open flash point below 79°C (173°F) as determined by the cleveland open cup tester.
ASTM D-6/D-1754 ; AAHSTO T-47/T-179; According SNI 06-2440-1991 For determining the loss in mass (exclusive of water) of asphaltic compounds after heating.
ASTM D-5 / AASHTO T-49 For determining consistency of bituminous materials
Consist of :
BI-231A Penetrometer : Electric control box, 220 V-AC variable timer, ON-OF and 1START switch for automatic plunger release cast alumunium frame, 4 1/2″ dial indicator, 400 x 0.1 mm dial, knob control manual electric, weight of needle and flunger : 50 gr. 1 set
Penetration Needle : Steel needle with brass shank, 1 mm dia 2 pcs
ASTM D-113 / AASHTO T-51; According SNI 06 -2432-1991 For determining ductility of formed asphalt/ cement or semi solid bitument by measuring distance of elangation before breaking point when two end of briquet are pulled a part at a specific speed and temperature.
Consist of :
Ductility Mold : Form sample shape and hold end during test made of brass, provided with base. 1 set
Ductility Machine : Electric 220 V-AC, stainless steel bath, provided with temperature control. 1 set
Pulling speed : 5 cm/min, / Travel range : 150 cm.
Dimension (l x w x h): 244 x 80 x 80 cm/ Gross weight: 150 Kg
The use automatic compaction will result in consistensi and repeatable laboratory specimens, suitable for ASTM or BS Standard. Testing houses and design consultants who use the marshall methode of mix design will benefit from automatic compaction apparatus, which releses staff for other work during the compaction process.
Automatic Compactor Machine : Heavy-duty welded steel construction 1 unit
The equipment is suitable for operation on 300 Watt, 220 V-AC, 50 Hz, 1 Phase. Automatic counter, module system for easy maintenance ON-OF-RUN-STOP-RESET- 500 Blow.
Compaction Mould 4″ : 4 inch diameter, 3 inch height, with collar and base plate machine steel, galvanized. 1 pcs
Compaction Mould 6″ : 6 inch diameter, 3 1/2 inch height, with collar and base plate machine steel, galvanized. 1 pcs
Compaction Hammer 10 lbs : The standard hammer has a 4,536 kg (10 lbs) sliding weight with a free fall 457 mm. 1 set
Compaction Hammer 22.5 lbs : The hammer has a 10.206 kg (22.5 lbs) sliding weight with a free fall 457 mm. 1 set
Compaction Pedestal : Comprising 300 mm square x 25mm thick steel plate secured 200mm square x 45 inchi high wooden block, the specimen mould, clamp and hammer guide are fitted to the plated, provided with compaction hammer guide stand 650mm height. 1 set
Standard supply with instruction manual books
Overal Dimension (l xwxh) : 400 x 450 x 1800 mm approx/ Weight (approx) : 200 Kg
Percentage Refusal Density (PRD) is defined as the ratio of the initial dried bulk density of the sample to the final density (refusal density) expressed as a percentage. The methode is the definitive test for determining the degree of compaction of bituminous pavements. The test is intended for quality control purposes. The sample bulk density is determined by weighing in air and water. It is then heated in a split mould and compacted to refusal using a vibrating hammer. The final density is obtained by weighing in air and water.
The one set consist of :
Vibrating Hammer Machine : Suitabble for compacting asphalt samples electric consumption 220 V, 50-60 Hz, 1 phase. Supplyed complete with carrying case. 1 unit
Small Tamping Foot : 102 mm diameter 1 pcs
Large Tamping Foot : 146 mm diameter 1 pcs
Shank : 300 mm shank for tamping foot 1 pcs
Split Mould : 4 inch mould diameter, split type, with base plate 1 pcs
Split Mould : 6 inch mould diameter, split type, with base plate 1 pcs
Dimension (l x w x h): 67x 42 x 23 Cm / Gross weight: 40 Kg
ASTM D-1559 / AASHTO T-245 / SNI 06-2484-1991 For determining the resistance to plastic flow of cylinder specimen of bituminous paving mixture loaded on the lateral surface by means of the marshall apparatus
Consist of :
Compression Machine : Steel frame electric, 220 V-AC, 1/2 HP 1 Phase speed : 2″ per-minute. 1 set
Compaction Mold : Machine steel, plated, 4inch dia., 3inch height, with collar and base plate. 1 set
Stability Mold : Cast alumunium, split type 4 inch i.d., 4inch wide 1 set
Compaction Hammer : Machine steel, plated 10 lbs, hammer weight 18 inch drop height. 1 set
Compaction Pedestal : Wooden base with steel platen 1 set
Comprising 300 mm square x 25mm thick steel plate secured to an 200 mm square x 45 inch high wooden block.